Blog / Flooring
Anderson Tuftex Flooring Review (2026)
An installer’s look at Anderson Tuftex: 117 engineered hardwood floors in white oak, ash, hickory, pecan and walnut, with veneers from 1.2 mm to 6 mm.

Quick answer
- Where the numbers come from
- The range side by side
- Veneer thickness is the spec that varies most
- Most of the range can go anywhere in a Toronto house
- Oil or aluminum oxide, and almost all of it low sheen
- What to check before you buy
- What it costs installed
- Buying Anderson Tuftex flooring in Toronto
- Every Anderson Tuftex floor we carry
- Frequently asked questions
Where the numbers come from
Every figure below comes from the spec sheets of the 117 Anderson Tuftex floors on our site as of November 2026. Where a sheet does not state something, we say so rather than fill the gap. We have not run our own wear tests and we do not give star ratings.
The range side by side
Veneer thickness is the spec that varies most
The veneers on these sheets run from 1.2 mm to 6 mm. The most common is 3 mm, on 25 sheets, followed by 4 mm and 2 mm on 17 each, 1.2 mm on 14, and 4.5 mm and 6 mm on 6 each.
The veneer is the real wood on top of the core, and it decides whether the floor can ever be sanded back to bare wood. A 1.2 mm veneer, as on Noble Hall, is best treated as a floor you recoat rather than sand. At 4 mm and above there is enough wood for a full sanding and refinish later in the floor’s life, which matters in a busy family room with kids and a dog.
Wire-brushed is the most common surface (Wire-brushed on 39 sheets, Wirebrushed on 22), and the open texture helps hide the fine scratches pets leave. If you prefer a flat, clean board, 29 sheets list a Smooth texture.
Most of the range can go anywhere in a Toronto house
On the sheets, 90 list above, on or below grade, 78 allow nail, staple, glue or floating, and 81 answer Yes to radiant heat, with 7 more listed as Compatible.
Engineered construction is what makes this possible. The layered core moves far less than solid wood through Toronto’s dry winters and humid summers, so the boards can float or be glued over a basement slab or condo concrete, and sit over in-floor heat. Most condo boards also set rules for acoustic underlay, so check yours before choosing a method.
There are exceptions. Eight sheets are glue-down only, including herringbone such as Biscotti European Ash Herringbone, and 6 sheets allow nail, staple or glue but not floating. Thickness runs from 1/2 to 3/4, and a thicker board plus underlay raises the floor at doorways and stair nosings, so plan the transitions early.
Oil or aluminum oxide, and almost all of it low sheen
The most common finish is UV aluminum oxide at 7% gloss, on 43 sheets. Another 15 sheets use UV oil at 7% gloss, and other aluminum oxide sheets list 9% or 13% gloss.
Aluminum oxide is a hard, cured film on top of the wood that needs little more than cleaning, but a deep scratch in it cannot be touched up in place. UV oil sits in the wood instead; the Nocturne sheet notes it can be refreshed at home with cleaning and a new coat of oil. The trade is that an oiled floor wants that re-oiling from time to time.
Low gloss across the range is a practical choice. A matte surface shows less dust, fewer scuffs and less glare from big condo windows than a shiny one.
What to check before you buy
The veneer on your floor. Between 1.2 mm and 6 mm it decides whether the floor can ever be sanded and refinished.
Glue-down or floating. Some sheets, including herringbone, are glue-down only, which changes subfloor prep and what a condo board will approve.
The warranty for that floor. Only 34 of the 117 sheets state a warranty, so ask us for the terms on the specific design before you order.
What it costs installed
Engineered hardwood is from $4.90 per square foot nailed or glued, including glue and nails. Herringbone and other patterns are quoted per job. This is installation only; the floor itself, disposal, trim and levelling are priced on top, and the full list is on our flooring installation cost page. For how we install it, see our page on hardwood flooring installation in Toronto.
Browse Anderson Tuftex in our shop: engineered hardwood. Send us your square footage for a free quote.
Typical of the range: Nocturne Heritage Oak, Ballet European Ash Herringbone and Raw Umber Valencia Walnut.
Doing the stairs at the same time? See our staircase renovation in Toronto, about $7,000 a flight.
Buying Anderson Tuftex flooring in Toronto
We carry Anderson Tuftex in engineered hardwood and install it across Toronto and the GTA. Our installers travel as far as Wasaga Beach, Niagara Falls and Castleton. Send your square footage for a free written quote, or book the free in-home measure and we will bring samples.
Every Anderson Tuftex floor we carry
All 117 Anderson Tuftex floors on our site, by collection. Tap a collection to see it as a group, or a colour to open that floor.
Engineered hardwood
Frequently asked questions
Can Anderson Tuftex go in a Toronto basement?
Most of the range can. On 90 sheets the installation level reads above, on or below grade, and 78 allow nail, staple, glue or floating, so the floor can float or be glued over a concrete slab. We check the slab for moisture and flatness when we measure.
Does Anderson Tuftex work over radiant heat?
On 81 sheets the answer is Yes, and 7 more say Compatible. Engineered boards cope with the warming and cooling of in-floor heat much better than solid wood. Not every sheet states it, so we confirm for the floor you pick.
Can an Anderson Tuftex floor be sanded and refinished?
It depends on the veneer, which runs from 1.2 mm to 6 mm. A 1.2 mm or 2 mm veneer should be treated as a floor that is recoated rather than sanded. Veneers of 4 mm and up leave enough wood for a full sanding later on.
What is the difference between the UV oil and aluminum oxide finishes?
Aluminum oxide is a hard cured film on the surface that needs little care but cannot be spot-repaired. UV oil, on 15 sheets at 7% gloss, sits in the wood and can be refreshed at home with cleaning and a new coat of oil. Oiled floors want that re-oiling from time to time.
What warranty comes with Anderson Tuftex?
Where a sheet states it, the warranty is 50 year limited residential, and a few sheets add a 5 year light commercial limited warranty. Only 34 of the 117 floors state a warranty at all. Ask us for the terms on the exact floor before you order.
Keep reading

























